• European-made range of small instruments on pages E1 - E3

DIGITAL RADIATION METERS
Small and light enough to go anywhere, yet sensitive enough to detect minuscule amounts of gamma, beta or X-rays.
Uses a Geiger-Muller tube detector for scanning lab work areas and clothing for traces of radioactivity after clean up. Operation is simple enough for use in science education. Also excellent for emergency responders, mining, Hazmat or any area of potential radiation exposure. The metre emits a chirping sound with each count that increases with radiation intensity. A loud 95db audible alarm can be set at any point within the meter's range. Adjustable auto power off prolongs battery life and can also be disabled. The 9-Volt battery lasts 50 hours at normal background levels. Indicates when the battery is low or the reading over range. Each unit comes in a soft carrying case with a battery and a certificate of compliance indicating that it has been tested in a Cs-137 field for two points of linearity and overall operation. E840024 comes with a certificate of compliance. Also available with a full N.I.S.T. traceable certificate of calibration - E840024C.
Dimensions: 143 x 74 x 34mm.
Weight: 176g.

Specifications
Range	0.1 ~ 199.9 uSv/hr 0.1 ~ 19.99 mRem/hr
Accuracy	±15%
Energy response	30KeV ~ 1.5MeV beta, gamma and x ray radiation

Optional Accessories
E840090 Water resistant instrument pouch

E840024 Digital radiation meter AUD431.00 Availability
E840024C Digital radiation meter, certified AUD606.00 Availability

ELECTROMAGNETIC FIELD TESTER
Measures electromagnetic emissions from electrical power lines and power transmission, computers, HVAC, audio/video, and other electrical appliances and equipment. While evidence of the carcinogenic effect of such electromagnetic emissions is still inconclusive, it is recommended to avoid excessive exposure over long periods of time. Reads milli-Gauss and micro-Tesla on a large 32mm high display. The display indicates when the object being measured is out of range as well as when the battery is low. Features both standard and maximum hold. Powered by a standard 9V battery lasting approximately 100 hours.
Comes with battery, instructions, and a soft carrying case.
Dimensions: 130 x 56 x 38mm
Weight: 170g

Available with NIST traceable certificate of calibration - E840045C

Unit of Measure	Range	Resolution	Accuracy
milli-Gauss	0.1 ~ 2000 mG	0.1 ~ 1	±2.5% + 3d @50/60Hz
micro-Tesla	0.01 ~ 200μT	0.01 ~ 0.1	±2.5% + 3d @50/60Hz

Optional accessories
E840090 Water resistant instrument pouch

E840045 Electromagnetic field tester/ Gauss meter AUD126.00 Available

RADIO FREQUENCY EMISSIONS METER
Evaluate the Radio Frequency (RF) emissions of mobile phones, radio and TV transmission towers, wireless cameras, Wi-Fi and LAN detection and installation, microwave oven leakage and other environmental safety concerns. Designed for measuring and monitoring the electromagnetic field radiation intensity - radio frequency, including microwaves. Radio Frequency is the range of electromagnetic frequencies above the audio range and below infrared light.

Features maximum and minimum hold, an audible alarm, and a zero adjustment to eliminate background EMF. The display also indicates overload and low battery.
Comes with a soft carrying case and standard 9V battery, which provides approximately 100 hours of use.
Dimensions: 130 x 56 x 38mm
Weight: 170g
The metre is calibrated precisely on the frequency value of 2.45 GHZ.

Specifications
Display	3¾ digits, maximum reading 3999
RF Power density	0.003~2.700 mW/cm²
RF Frequency	50MHz ~ 3.5GHz
Microwave frequency	2450MHz
Resolution	0.001mW/cm²
Accuracy	±2dB @ 2.45GHz ±50MHz
Axis	Single
Alarm	@ readings >1mW/cm²
Operating temperature	5°C ~ 40°C
Operating RH	<80% RH

E840046 Radio frequency meter, broad range AUD206.00 Availability

OXYGEN METER
Easily portable and designed for simple one-hand operation.
Reads oxygen in air for environmental studies, IAQ, bio-technology (for oxygen incubators and anaerobic cultivators), food storage and refrigeration, testing fire alarm and fuel cell systems. The fast, highly reliable, galvanic oxygen sensor is unaffected by acidic gases such as CO2. Simultaneously displays O2 concentration and air temperature in °C or °F.
Features hold, min/max, a low battery indicator, ATC and auto-power-off.
Comes with 4 AAA batteries and a soft carrying case with a belt loop and shoulder strap.
Dimensions: 180 x 40 x 40mm
Weight: 175g

Specifications

	Range	Resolution	Accuracy
O2	0 ~ 30%	0.1%	± (1% reading + 0.2% O2)
Temp	0 ~ 50°C	0.1°	± 0.8°C

E800047 Oxygen meter, 0 - 30% AUD368.00 Availability

COMPACT ENVIRONMENTAL QUALITY METER
For environmental testing anywhere. Combines a light meter, humidity meter, thermometer, anemometer into a single compact unit weighing only 160g. Own the equivalent of 4 meters for about the price of any one of them. Features dual display with low battery and over range indications, touch-tone buttons, max-min, auto power off and hold functions. Comes ready to use with soft carrying case, wrist strap, instructions and a 9V battery.
Dimensions: 150 x 65 x 30mm
Weight: 160g

	Range	Resolution	Accuracy
°C Ambient	0~50	0.1	±1.2°C
°C Type K	-100~1300	0.1	±(1% + 1°C)
RH	10~95%	0.1	±6% 30 ~ 60RH otherwise ±8%
Airspeed m/s km/h mile/h knots ft/min	0.4 ~ 25.0 1.4 ~ 90.0 0.9 ~ 55.9 0.8 ~ 48.6 80 ~ 4930	0.1 0.1 0.1 0.1 1	±(3% + 2d) ±(3% + 2d) ±(3% + 2d) ±(3% + 2d) ±(3% + 20ft/min)
Lux	0~20,000	1	±(5% + 4d)
Foot candle	0~2,000	0.1	±(5% + 4d)

E850070 Compact environmental quality meter AUD188.00 Availability

ENVIRONMENTAL QUALITY METER
Using interchangeable probes this versatile metre reads airspeed, temperature, RH and light. The user can order probes for the parameters currently required and add additional probes in the future. Intelligent probes electronically retain calibration information. No recalibration is required when changing probes. The display simultaneously reads temperature in user selectable °C & °F and all measurements are automatically temperature compensated. RS-232 port enables communication with a computer. Also features auto power off, hold and min-max. Fold out easel back and a tripod screw. Comes with 9V battery and a hardshell foam-lined carrying case with room for one or two probes.
Dimensions: (main unit):195 x 68 x 30mm
Weight: (main unit): 250g

Thermocouple probes
Type J and K thermocouple probes for the following applications:

• Immersion and general purpose
• Penetration
• Surface
• Ambient

Technical note - Thermocouple probes specifications
Ask for prices

	Range	Resolution	Accuracy
Thermocouple Probes
Type K	-50~1300°C	0.1	±0.2% +1°C
Type J	-50~1150°C	0.1	±0.2% +1°C
Anemometer Probe E850072
M/s	0.4~25.0	0.1	±2% +2d fs
Km/h	1.4~90.0	0.1	±2% +2d fs
Mile/h	0.9~55.9	0.1	±2% +2d fs
Knots	0.8~48.6	0.1	±2% +2d fs
Ft/min	80~4930	1	±2% +20 ft/min
°C	0~50	0.1	±0.8°
Metal Anemometer Probe E850077
M/s	0.5~40.0	0.1	±2% +2d fs
Km/h	1.8~144.0	0.1	±2% +2d fs
Mile/h	1.1~89.4	0.1	±2% +2d fs
Knots	1.0~78.1	0.1	±2% +2d fs
Ft/min	100~7880	1	±2% +20 ft/min
°C	0~60	0.1	±0.8°
Mini Extension Anemometer Probe E850073
M/s	0.4~12.0	0.1	±2% +2d fs
Km/h	1.4~43.2	0.1	±2% +2d fs
Mile/h	0.9~26.8	0.1	±2% +2d fs
Knots	0.8~23.3	0.1	±2% +2d fs
Ft/min	80~2358	1	±2% +20 ft/min
°C	0~50	0.1	±0.8°
Humidity Probe E850074, with N.I.S.T tracable certificate of calibration E850074C
RH	10%~95%	0.1%	>70%RH ±5%rdg +1%RH <70%RH ±5%RH
°C	0~50	0.1	±0.8°
Light Probe E850075, with N.I.S.T tracable certificate of calibration 850075C
Lux	2,000	1	±5%rdg +2d
Lux	20,000	10	±5%rdg +2d
Lux	50,000	100	±5%rdg +2d
Foot Candle	200	0.1	±5%rdg +2d
Foot Candle	2,000	1	±5%rdg +2d
Foot Candle	5,000	10	±5%rdg +2d
IR Temperature E850076 D/S 7:1 Emissivity 0.95
°C	-10~300	1	±3%rdg or ±3oC which ever is greater

Optional accessories
E840090 Water resistant instrument pouch
E840092 Bench-top tripod
E840093 Field tripod
E840057 RS232 1.2m cable. A standard RS232 cable is not sufficient, the instrument has a unique plug.
E840094 USB cable
E850080 Data acquisition software

Available with NIST traceable certificate of calibration - E850074C, E850075C

E850071 Environmental quality meter AUD164.00 Availability
E850072 Anemometer probe for E.Q. meter AUD132.00 Availability
E850073 Mini extension anemometer probe for E.Q. meter AUD277.00 Availability
E850074 Relative humidity probe for E.Q. meter AUD95.00 Availability
E850075 Light probe for E.Q. meter AUD80.00 Availability
E850076 IR temperature probe for E.Q. meter AUD86.00 Availability
E850077 Metal anemometer probe for E.Q. meter AUD164.00 Availability

HYBRID POWERED ENVIRONMENTAL QUALITY METER
Parameters

• Air speed
• Humidity
• Light
• Temperature

A unique hand powered generator enables environmental quality measurements with or without batteries. Combines an anemometer, hygrometer, thermometer and light metre in a single rugged unit. Also reads any type-K thermocouple probe. The large dual LCD screen displays results and indicates low battery and out of range. Features touch-tone buttons, min/max, auto power off and hold functions. Comes ready to use in a foam lined hard shell carrying case with instructions, 9V battery, tripod back and a tripod screw.
Dimensions: 175 x 75 x 45mm
Weight: 415g

E850068	Range	Resolution	Accuracy
°C ambient	0 ~ 50	0.1	±1.2°C
°C Type K	-100 ~ 1300		±(1% + 1°C)
RH	10 ~ 95%		<70%RH ±4% >70%RH ±(4% rdg + 1.2%RH)
Airspeed m/s	0.4 ~ 25.0		<20 m/s ±3% fs >20 m/s ±4% fs
Airspeed km/h	1.4 ~ 90.0
Airspeed mile/h	0.9 ~ 55.9
Airspeed knots	0.8 ~ 48.6
Airspeed ft/min	80 ~ 4930	1
Lux	0 ~ 2,000 1800 ~ 20,000	1 10	±5% rdg + 8d
Foot Candle	0 ~ 204.0 170 ~ 1860	0.1 1

Optional accessories
E800060~77 Type-K thermocouple probes
E840090 Water resistant instrument pouch
E840093 Field tripod

E850068 Hybrid powered environmental quality meter AUD275.00 Availability

ENVIRONMENTAL QUALITY METER WITH SOUND
Measures

• Air speed
• Humidity
• Light
• Sound
• Temperature

Combines an anemometre, hygrometre, thermometre, sound and light metre in a single hand-held unit. Also reads any type-K thermocouple probe. Results are displayed on a large dual LCD screen with low battery and out of range indications. Features touch-tone buttons, min/max, auto power off and hold functions. Comes ready to use in a soft carrying case with RS232 computer port instructions, 6 AAA batteries, tripod back and a tripod screw.
Dimensions: 255 x 75 x 35mm
Weight: 330g

E850069	Range	Resolution	Accuracy
°C ambient	0 ~ 50	0.1	±1.2°C
°C Type K	-100 ~ 1300		±(1% + 1°C)
RH	10 ~ 95%		<70%RH ±4% >70%RH ±(4% rdg + 1.2%RH)
Airspeed m/s	0.4 ~ 30.0		<20 m/s ±3% fs >20 m/s ±4% fs
Airspeed km/h	1.4 ~ 108.0
Airspeed mile/h	0.9 ~ 67.0
Airspeed knots	0.8 ~ 58.3
Airspeed ft/min	80 ~ 5910	1
Lux	0 ~ 2,000 1800 ~ 20,000	1 10	±5% rdg + 8d
Foot Candle	0 ~ 204.0 170 ~ 1860	0.1 1
dB	35 ~ 130	0.1	25+5°C ±1.5dB

Optional accessories
E800060~77 Type-K thermocouple probes
E840057 RS232 cable
E840094 RS232 to USB adaptor cable
E840097 AC Adaptor
E840093 Field tripod
E850016 2-point acoustical calibrator
E850080 Software

Available with NIST traceable certificate of calibration - E850069C

E850069 Environmental quality meter with sound AUD296.00 Availability

ADVANCED LIGHTMETER
Monitor light levels anywhere with fast, stable and accurate response. Results are easily read on the extra large LCD (38.1mm) with bar graph, low battery and over range indications. The colour and cosine corrected sensor meets C.I.E. photopic spectrum. Offers peak function and a unique and very useful ability to compensate for the different colors of tungsten, fluorescent, mercury and sodium lights, with the push of a button. The result is readings true to actual lighting conditions. Also features RS232 computer output, max-min, auto power off, external zero adjustment, hold function and a tripod back. Comes ready to use with a 9V battery, instructions, soft padded case with shoulder strap, and a detachable sensor with cover for easier replacement or repair.
Meter dim.: 200 x 68 x 30mm
Weight: 280g

Available with NIST traceable certificate of calibration - E840022C

Optional accessories
E840057 RS232 cable. A standard RS232 cable is not sufficient, the instrument has a unique plug.
E850080 Software
E840090 Water resistant instrument pouch
E840092 Bench-top tripod
E840093 Field tripod

ESB840022 Advanced light meter AUD175.00 Available

VISIBLE LIGHT DATALOGGER WITH SD CARD
Reads lux, foot candles and functions as a type K or J thermometer. Records data onto standard SD memory cards (like a digital camera). When full, simply exchange SD cards for unlimited data storage. The removable SD card is easy to transport and insert into a computer's memory card slot or SD card adapter. Uploads preformatted data to Excel, without the need for software and cables. Additional SD cards are readily available in a variety of memory sizes. Can also manually record 99 readings for on-screen review or stream data directly to a computer using the optional software and cables.
Each data set includes lux or foot candle reading, time and date. Features push button zero adjustment, min/max, auto power off, low battery indicator and hold function.
This well made unit is extremely accurate with fast response times, and includes a fold-out tripod and large easy-to-read backlit LCD.
Comes ready to use in a soft carrying case complete with a detachable colour-corrected probe that meets the C.I.E. photopic spectrum, 6 AA batteries, instruction manual and a 2GB SD card.
Dimensions: 177 x 68 x 45mm
Weight: 489g

Optional accessories
E800060~77 Type K thermocouple probes
E840057 RS232 computer cable
E840059 Additional 2GB SD card
E840090 Water resistant instrument pouch
E840093 Field tripod
E840094 USB computer cable
E840097 AC adaptor
E850080 Software

	Range	Res.	Accuracy
Lux	2,000	1	± (4%+2 dgt) rdg
	20,000	10
	100,000	100
Foot Candle	200	0.1
	2,000	1	± (4%+2 foot candle) rdg
	10,0001	10	± (4%+20 foot candle) rdg
Type K	-50 ~ 1300°C	0.1	± (0.4% + 1°C ) fs.
Type J	-50 ~ 1200°C

E850007C comes with NIST traceable certificate of calibration.

E850007 Visible light/ temp. datalogger with SD card AUD266.00 Availability
E850007C Visible light/ temp. datalogger with SD card, certified AUD303.00 Availability

UV LIGHT METERS
Applications

• Measure damaging UV (ultraviolet) light in the environment and museums.
• UV degradation studies in the pharmaceutical, cosmetic, semiconductor, printing, window tinting and other industries.
• Laboratory chromatography, electrophoresis and forensics.
• Test UV sterilisation and dermatology lamps in hospitals.

UV light intensity appears on the large backlit display in either µW or mW/cm² while the small lower display simultaneously shows minimum, maximum, average and recorded data. Up to 20 data points can be recorded automatically at a variety of intervals. Features zero point reset, hold and low battery indicator.
Comes in a protective, hard foam lined carrying case complete with a UV probe, tripod screw, magnetic mount and a 9V battery.
Model E850009 measures long and medium wave UV-A/B for applications such as forensics, chromatography, electrophoresis and dermatology.
Model E850010 measures short wave UV-C light for applications such as UV light fume hoods, UV sterilisation, industrial glass and non-destructive testing.
Dimensions: 145 x 55 x 40mm
Weight: 135g

Available with NIST traceable certificate of calibration - E850009C and E850010C

Cat. No.	Wavelength	Calibration Point	UV Range	Resolution	Accuracy
E850009	280 ~ 400 nm	365 nm	1 µW/cm² ~ 40.00 mW/cm²	1 µW and 0.01 mW/cm²	±4% ±1 digit (@23 ±5°C)
E850010	220 ~ 275 nm	254 nm

Optional accessories
E840090 Water resistant instrument pouch
E840092 Bench-top tripod
E840093 Field tripod

E850009 UVA/B Light meter AUD209.00 Available
E850010 UVC Light meter AUD595.00 Availability

ANEMOMETERS
These pen-style meters are ideal for field studies and HVAC. They measure

• wind speed in four units of measure
• temperature in °C & °F
• humidity
• dew point

measures barometric pressure in three units of measure.
Both models display two parameters simultaneously and indicate when batteries are low. They also feature hold, min-max and auto power off. Ready to use with four AAA batteries and a soft carrying case with belt loop.
Dimensions: 205 x 48mm
Weight: 182g with batteries

	Range	Resolution	Accuracy
Airspeed ft/min	80 ~ 5910	1
Airspeed m/s	0.4 ~ 30	0.1	>20 m/s ± 4% fs
Airspeed km/h	0.4 ~ 30
Airspeed mph	0.9 ~ 67
Airspeed knots	0.8 ~ 58
Temperature °C	0 ~ 50°
RH	10 ~ 95%		>70%RH ± (3% rdg. + 1%RH)
Dew Point °C	-26 ~ 48°	0.01	Sum of the Temp + RH accuracy of the measurement
Barometric Pressure
hPa	10 ~ 999 1000 ~ 1100	0.1 1	±1.5 ±2
mmHg	7.5 ~ 825	0.1	±1.2
inHg	0.29 ~ 32	0.01	±0.05

E850022 Anemometer/ RH/ barometer AUD187.00 Availability

ANEMOMETER/ TEMPERATURE DATALOGGER WITH SD CARD
Reads air velocity and temperature and functions as a type K or J thermometer. Records data onto standard SD memory cards. When full, simply exchange SD cards for unlimited data storage. The removable SD card is easy to transport and insert into a computer's memory card slot or SD card adapter. Uploads preformatted data to Excel, without the need for additional software and cables. Additional SD cards are readily available in a variety of memory sizes.
Can also manually record 99 readings for on-screen review or stream data directly to a computer using the optional software and cables.
Each data set includes air speed, air temperature, time and date. Features min/max, auto power off, low battery indicator and hold function.
This well made unit is extremely accurate with fast response times, and includes a fold-out tripod and large easy-to-read backlit LCD.
Comes ready to use in a soft carrying case complete with a detachable probe, 6 AA batteries, instruction manual and a 2GB SD card.
Dimensions: 177 x 68 x 45 mm
Weight: 489g

Optional accessories
E800060~77 Type K thermocouple probes
E840057 RS232 computer cable
E840059 2GB SD card
E840090 Water resistant instrument pouch
E840093 Field tripod
E840094 USB computer cable
E840097 AC adapter
E850080 Software

	Range	Res.	Accuracy
Ft/min	79 ~ 6890	1	± (2%+40 FPM) rdg
Km/h	1.4 ~ 126	0.1	± (2%+0.8 Km/h) rdg
mph	0.9 ~ 78.3		± (2%+0.4 mph) rdg
Knots	0.8 ~ 68		± (2%+0.4 Knots) rdg
m/S	0.4 ~ 30		± (2%+0.2 m/S) rdg
Type K	-50 ~ 1300°C		± (0.4% + 1°C ) fs.
Type J	-50 ~ 1200°C

E850023 Anemometer/ temp. datalogger with SD card AUD394.00 Availability

HOT WIRE ANEMOMETER DATALOGGER WITH SD CARD
Reads air velocity and temperature and functions as a type K or J thermometer. Records data
onto removable, standard SD memory cards (like a digital camera). When full, simply exchange SD cards for unlimited data storage. The removable SD card is easy to transport and insert into a computer's memory card slot or SD card reader. Uploads pre-formatted data to Excel, without the need for additional software and cables. Additional SD cards are readily available in a variety of memory sizes. Can also stream data directly to a computer using the optional software and cables. Each data set includes air speed, air temperature, time and date. Features min/max, auto power off, low battery indicator and hold function. This well made unit is extremely accurate with fast response times, and includes a fold-out tripod and large, easy-to-read backlit LCD. Comes ready to use in a soft carrying case complete with a detachable telescopic probe, 6 AA batteries, instruction manual and a 2GB SD card.
Dimensions: 177 x 68 x 45 mm. weight: 460 g.

	Range	Resolution	Accuracy
Ft/min	40 - 3940	1	± (1%+20 fpm) fs
Knots	0.4 - 38.8	0.01 - 0.1	± (1%+0.2 Knots) fs
m/S	0.2 - 25.0		± (1%+0.1 m/S) fs
Km/H	0.7 - 72.0		± (1%+0.3 Km/h) fs
mph	0.5 - 44.7		± (1%+0.2 mph) fs
Type K	-50 - 1300°C	0.1	± (0.4% + 1°C ) fs
Type J	-50 - 1100°C
Air tempture	0 - 50°C		0.8°C

Optional accessories
E800060-77 Type K Thermocouple Probes
E840057 RS232 Computer Cable
E840059 2GB SD Card
E840090 Water Resistant Instrument Pouch
E840093 Field Tripod
E840094 RS232 to USB Adaptor Cable
E840097 AC Adaptor
E850080 Software

E850024 Hot wire anemometer, with SD card logger AUD394.00 Availability

PEN VAC™
Pen Vac™ gives a superior means for the handling of small, flat surface objects. Pen Vac is ideal for electron microscopy and histology work. It can be used to move grids, pick up stubs, align membranes, work with glass slides, cover slips and much more. Additionally, Pen Vac is useful in the electronics assembly industry, for jewellers, model builders etc.

Features

• Lifts up to 50 grams.
• Totally self-contained vacuum.
• Light-weight: less than 30 grams.
• Fits into a pocket like a pen.
• Brushed aluminium body.
• Optional storage compartment for vacuum tips and cups.
• No power supply needed.
• Available in various sizes.
• Interchangeable vacuum probes.

Pen Vac™ is supplied with:
A variety of vacuum probes, including an attached vacuum cup, available with plastic or aluminium hubs. Straight and angled to suit your applications. The stainless steel needles of the probes are 12mm long.
Vacuum cups are available in a wide range of materials. We offer the Static Dissipative and the Conductive Cups that provide ESD protection for electrostatic discharge of sensitive components. Cups come in three sizes: 3.2mm, 6.4mm and 9.5mm.

Set consists of:
One pen with 3 angled and 3 straight probes and matching cups, one of each size.

E230 Pen-Vac system AUD133.00 Availability
E2301 Probes and cups for Pen-Vac™, small AUD17.00 /pack/2 Available
E2302 Probes and cups for Pen-Vac™, medium AUD17.00 /pack/2 Available
E2303 Probes and cups for Pen-Vac™, large AUD17.00 /pack/2 Availability

VACUUM PICK-UP SYSTEM
Handles small, delicate objects without scratching, breaking or pinching. The system avoids contamination of parts and performs the same functions as tweezers, such as sorting, picking up, holding, carrying and transferring. It is also an alternative way for handling coverslips without the use of forceps.
Features

• Picks up grids faster and easier than tweezers. WARNING: Never use this device on coated grids.
• Quiet operation
• Eliminates all tweezer damage to grids.
• Good suction (produces 14" Hg vacuum and an air flow of 125 cubic inches/minute). Can pick up aluminium stubs.
• Can be used as a tool to pick up glass slides, cover slips, wafers, thin film samples etc.

Double-insulated (220V, 60Hz, 2-wire). Lightweight, completely assembled and ready for immediate operation as soon as the proper tip is selected and installed. Vacuum is created at the tip by placing the finger over the control hole on the anodised aluminium vacuum pen. To break the vacuum, just remove finger from the hole. The vacuum generator measures 114 x 70mm; it has an adjustable vacuum pressure control from 1" Hg to 15" Hg.

Vacuum pick-up system, complete set includes:
Vacuum generator
Aluminium vacuum pen
Five vacuum tips
Set of seven rubber vacuum cups (sizes: 14.3mm, 12.7mm, 11.1mm, 9.5mm, 7.9mm, 6.4mm and 4.8mm)
In-line filter
Vacuum tubing, 1.2m

These components are also available individually.

Operating instructions

E231 Vacuum pick-up system, complete set AUD331.00 Availability
E231-1V Vacuum generator AUD200.00 Availability
E231-2P Vacuum pick-up pen AUD71.00 Availability
E231-3F Vacuum pick-up in-line filter AUD28.00 Availability
E231-4T15 Vacuum pick-up tip, SS, 15 gauge AUD22.00 Availability
E231-4T16 Vacuum pick-up tip, SS, 16 gauge AUD17.00 Availability
E231-4T21 Vacuum pick-up tip, SS, 21 gauge AUD17.00 Availability
E231-4T22 Vacuum pick-up tip, SS, 22 gauge AUD17.00 Availability
E231-4T23 Vacuum pick-up tip, SS, 23 gauge AUD17.00 Availability
E231-5C06 Vacuum pick-up suction cup, Ø 6.4mm AUD11.00 Availability
E231-5C07 Vacuum pick-up suction cup, Ø 7.5mm AUD11.00 Availability
E231-5C09 Vacuum pick-up suction cup, Ø 9.5mm AUD11.00 Availability
E231-5C11 Vacuum pick-up suction cup, Ø 11.1mm AUD11.00 Availability
E231-5C14 Vacuum pick-up suction cup, Ø 14.3mm AUD11.00 Availability
E231-5CSET Vacuum pick-up suction cups, set of 7 AUD48.00 Availability

UV LIGHT PEN,
This pen light uses new solid-state LED technology to offer a portable source of UV light built into a slim attractive pen. This new technology has a number of significant advantages over older products using UV fluorescent tubes and light bulbs.

Features

• A more compact, rugged and easily portable product, perfect for fieldwork.
• The 400nm output is just on the edge of the visible light spectrum, low enough to cause fluorescence yet inherently safer than lower UV wavelengths.
• Much longer battery life eliminates the need for power cords and battery packs. Powered by only four button cell batteries (included).
• Immediate output, no warm-up time.
• Much lower cost.

Specifications
Light source: high intensity InGaN LED
Wavelength: peak:400, Min:390, Max:410
Output power: 12,000 mW/M2
Optical rise time: 30 t, ns. Typical
Operating temperature: -4~176ºF
Dimensions: 135 x 10mm
Weight: 30g with batteries

ESA330005 Pen light, UV AUD35.00 Available

FORCE GAUGE WITH RS232 OUTPUT
Measure tension or compression anywhere or mount on the optional test stand and connect with software E850080 via the RS232 port to a computer for automated testing and process control. Display results right side up or upside down for compression or tension applications. The peak hold function works in both modes. Additional functions are     zero (tare), fast or slow response options, overload protection, and a low battery indicator. Supplied with a protective carrying case containing an extension rod with a full line of adapters and 6 AAA batteries.
Dimensions: 227 x 83 x 39mm
Weight: 569g

Force Gauge	Range	Resolution	Accuracy
Grams	3 ~ 5000	1	±(0.4%+ 1d) within 23 ± 5°C
Oz.	0.1 ~ 176	0.05
Newtons	0.03 ~ 49	0.01

Optional accessories
E840056 RS232 1.8m cable
E840094 RS232 to USB adapter cable
E850080 Software

E840061 Force gauge test stand - ask
Can be used with E840060 or any other force gauge. This stand includes a clamp for securing wires or other materials to the base of the stand for tension tests. The clamp may be removed to provide a flat base for compression tests.

Capacity	50kg
Travel	400mm
Dimensions	630 x 250 x 230mm
Weight	7kg

The software works with a number of Sper Scientific meters. It provides 3 displays, up to 8-channel simultaneous monitoring, high/low alarm, variable sampling times (2~3600 sec), and produces .mdb data files compatible with spreadsheets and databases.

Software system requirements

• At least one communications port
• VGA Monitor type or higher
• RS232 cable (E840057 sold separately), and
• Win 95: 16 mb memory, 486, 586 or higher, or
• Win 98, Windows ME, Windows XP: 32 mb mem, 586 or higher.

E840060 Force gauge AUD472.00 Availability
E850080 Software for force gauge AUD75.00 Availability

Accessories for Sper Scientific instruments

RS232 CABLE FOR SPER INSTRUMENTS
RS232 1.2m cable. For Sper instruments that have a unique plug (a standard RS232 cable is not sufficient).

E840057 RS232 Cable for Sper instruments AUD48.00 Availability

USB SERIAL ADAPTER
Enables all Sper Scientific meters with RS232 ports to be plugged into any computer's USB port. Compatible with Windows 95, 98, 98ME, 2000, XP. Comes with instructions and a CD containing drivers.

E840094 RS232 to USB adapter cable AUD17.00 /each Available

SOFTWARE FOR SPER SCIENTIFIC METERS
The RS232 software is used with the following products for logging data and further analysis:

1. K.J.T or K.J.T.R.S.E.type thermometer
2. pH /mV meter
3. Hygro-thermometer & psychrometer
4. Digital sound level meter
5. Anemometer
6. Manometer
7. Conductivity meter
8. IR Psychrometer
9. D.O. Meter

Suitable for other meters with a RS232 interface feature. This software is user-friendly.

E840052 Data logging software AUD80.00 /each Availability

BENCH-TOP TRIPOD
Pocket size tripod is stable when open yet folds to only 127 x 38 x 13mm for easy carrying and storage. Weighs under 57 grams. Usage height: 89mm. Both tripods fit any metre with a threaded tripod attachment.

E840092 Bench-top tripod AUD24.00 /each Available

FIELD TRIPOD
Lightweight at only 1 kg, yet strong and stable. Fliplever legs quickly lock into place at any height up to 1.47m and quickly fold down to 0.53m for carrying and storage. The height can be further adjusted with a geared, cranked elevator column. Features a 3-way adjustable head, self-leveling swivel feet, a bubble-level, carrying handle and an accessory hook. Comes in a zippered carrying case with a handle.

E840093 Field tripod AUD92.00 /each Availability

WATER RESISTANT INSTRUMENT POUCH
Fits all Sper Scientific Meters and helps protect them from the elements during field work. The pouch enables the user to read and operate the instrument inside while the probe extends outside. Has a carrying strap and a velcro sealed top.
Dimensions: 229 x 178mm
Warranty: 90 days

E840090 Water resistant instrument pouch AUD23.00 Available

RUBBER BOOT
Fits the following meters: E800004, E800007, E840045, E840046, E850014

E850000 Rubber instrument protector AUD13.00 Available