• Benchtop cleaners are on page E13

UNISONICS ULTRASONIC CLEANERS, ST SERIES
Unisonics industrial/commercial ultrasonic cleaners, the ST Series, is a high performance ultrasonic cleaning system. The single chamber device is used to clean surgical instruments and other hardware with sonic energy in a water detergent solution. The process generates a randomised sweep frequency through the ultrasonic bandwidth, which provides the most uniform fields of cavitation available in a 40KHz-process tank. The unit has been designed for use in surgery reprocessing areas, central processing departments and laboratories.

FEATURES

• Solid 304 grade stainless steel construction
• 0.9mm external walls, chamber is 1.6mm thick
• Integral plumbing is SS, drainage valve is welded into chamber
• Standard sizes ranging from 18 to 54 litres
• Electronic digital or mechanical timers
• Thermostat controlled heater (optional)
• Sweep frequency
• Polyester coated transducers
• Circuit breaker and air cooling of power circuits
• Rounded corner reflex design
• Stainless steel lid plus basket (standard in all models)
• Insulation
• EMC tested and approved

Most industrial cleaners are custom made, however, the following standard units are available.

To contact for further information see footer.

INDUSTRIAL/ COMMERCIAL ULTRASONIC CLEANER, 18L
Features

• Solid stainless steel construction (tank & enclosure)
• Mechanical timer
• Polyester coated transducers
• Sweep frequency
• Stainless steel lid & basket
• Insulation
• Outlet drain
• Cooling fan

Specifications
Tank dimensions (internal)

• Length: 300mm
• Width: 300mm
• Depth: 200mm
• Tank capacity: 18 litres
• Transducer power: 600 watts
• Operating frequency: 40kHz

Digital timer option available.
Download pdf

EST18M Industrial ultrasonic cleaner, 18L, mechanical timer - discontinued ask stock?
EST18MH Industrial ultrasonic cleaner, 18L, mechanical timer, heated ask stock?

INDUSTRIAL/ COMMERCIAL ULTRASONIC CLEANER, 27L
Features

• Solid stainless steel construction (tank & enclosure)
• Mechanical timer
• Polyester coated transducers
• Sweep frequency
• Stainless steel lid & basket
• Insulation
• Outlet drain
• Cooling fan

Specifications
Tank dimensions (internal)

• Length: 450mm
• Width: 300mm
• Depth: 200mm
• Tank capacity: 27 litres
• Transducer power: 600 watts
• Operating frequency: 40kHz

Digital timer option available.
Download pdf

EST27M Industrial ultrasonic cleaner, 27L, mechanical timer - discontinued ask stock?
EST27MH Industrial ultrasonic cleaner, 27L, mechanical timer, heated ask stock?

INDUSTRIAL/ COMMERCIAL ULTRASONIC CLEANER, 40L
Features

• Solid stainless steel construction (tank & jacket)
• Mechanical timer
• Polyester coated transducers
• Sweep frequency
• Stainless steel lid & basket
• Insulation
• Outlet drain
• Cooling fan

Specifications
Tank dimensions (internal)

• Length: 450mm
• Width: 450mm
• Depth: 200mm
• Tank capacity: 40 litres
• Transducer power: 900 watts
• Operating frequency: 40kHz

Digital timer option available.
Download pdf

EST40M Industrial ultrasonic cleaner, 40L, mechanical timer - discontinued ask stock?
EST40MH Industrial ultrasonic cleaner, 40L, mechanical timer, heated ask stock?

INDUSTRIAL/ COMMERCIAL ULTRASONIC CLEANER, 54L
Features

• Solid stainless steel construction (tank & jacket)
• Mechanical timer
• Polyester coated transducers
• Sweep frequency
• Stainless steel lid & basket
• Insulation
• Outlet drain
• Cooling fan

Specifications
Tank dimensions (internal)

• Length: 600mm
• Width: 450mm
• Depth: 200mm
• Tank capacity: 54 litres
• Transducer power: 1200 watts
• Operating frequency: 40kHz

Digital timer option available.
Download pdf

EST54M Industrial ultrasonic cleaner, 54L, mechanical timer - discontinued ask stock?
EST54MH Industrial ultrasonic cleaner, 54L, mechanical timer, heated ask stock?

CONSOLE ULTRASONIC CLEANERS
Like the above cleaners, these are frequently built to specifications. These tanks are on castors and dedicated to commercial tasks.
Ask for further information

CONSOLE ULTRASONIC CLEANER, 81L
Features

• Solid stainless steel construction (tank & enclosure)
• Mechanical timer
• Polyester coated transducers
• Rounded corner reflex design
• Sweep frequency
• Stainless steel lid & basket
• Insulation
• Outlet drain
• Cooling fan
• Locking castors

Specifications
Tank dimensions (internal)

• Length: 600mm
• Width: 450mm
• Depth: 300mm
• Tank capacity: 81 litres
• Transducer power: 1500 watts
• Operating frequency: 40kHz

Digital timer option available.
Download pdf

ESTCON81M Console ultrasonic cleaner, 81L, mechanical timer - discontinued ask stock?
ESTCON81MH Console ultrasonic cleaner, 81L, mechanical timer, heated ask stock?

CONSOLE ULTRASONIC CLEANER, 108L
Features

• Solid stainless steel construction (tank & enclosure)
• Mechanical timer
• Polyester coated transducers
• Rounded corner reflex design
• Sweep frequency
• Stainless steel lid & basket
• Insulation
• Outlet drain
• Cooling fan
• Locking castors

Specifications
Tank dimensions (internal)

• Length: 800mm
• Width: 450mm
• Depth: 300mm
• Tank capacity: 108 litres
• Transducer power: 1800 watts
• Operating frequency: 40kHz

Digital timer option available.
Download pdf

ESTCON108M Console ultrasonic cleaner, 108L, mechanical timer - discontinued ask stock?
ESTCON108MH Console ultrasonic cleaner,108L, mechanical timer, heated ask stock?

BRANSON SONIFIER® PRODUCTS

Branson Sonifier ultrasonic cell disruptors are versatile laboratory tools designed to apply high-frequency ultrasonic energy to biological and chemical processing to:

• Disrupt cellular structures
• Homogenize samples
• Emulsify materials
• Disperse or mix compounds
• Accelerate reactions

Sonifiers are able to process static samples from 1mL to greater than 500mL or flowing material up to 40L/h. Analog units are available in two power levels. Digitally-operated units are offered in three power levels and are suggested for applications requiring higher levels of process control or parameter measurement.

Analog Units
Sonifier analog cell disruptors and homogenizers are available in 200 watt (Model S-250A) and 400 watt (Model S-450A) models. These capable units are widely-used in laboratories to facilitate a wide range of biological and chemical processes.

Digital Units
The Sonifier S-250D 200 watt and S-450D 400 watt units offer all of the capability of the analog models, plus digital control for precise process control and parameter meaurement. They are particularly suitable for larger or more difficult samples.

The Sonifier S-150D 100 watt digital unit is a full-featured, lower power unit designed to effectively process the smaller samples often associated with genome and other biological research.

ANALOG UNITS - Models S-250A & S-450A

• Datasheet for S-250A & S-450A

DESCRIPTION
Branson Sonifier ultrasonic cell disruptor / homogenizers are versatile laboratory units suitable for a broad range of liquid processing applications such as:

• Biological cell disruption / homogenization
• Emulsification
• Reaction acceleration
• Dispersion
• Fine mixing
• Degasing

Each model consists of a power supply, a converter, and a mechanical probe or horn. The power supply/converter changes standard electrical power to high frequency mechanical energy, which is then applied to the horn, where it is further amplified for use (often with specialized accessories)

KEY FEATURES
Sonifier S-250A and S-450A analog ultrasonic processors include many features to make the technician's work easier.

• Two power levels - 200 Watt (S-250A)
  - 400 Watt (S-450A)
• Auto tuning for optimum performance under varying conditions
• Power output control to match power to the application
• Continuous or timed (0-15 minutes) operation to free technician for other activities
• Pulsed mode to minimize heat generation in thermally-sensative samples
• Broad process range from 1ml to over 500 ml per sample
• Power output meter to monitor power and permit reproducability
• Compact design limits required counter space
• Sloped front control panel for visibility and easy control access
• Includes a high-efficiency converter which requires no internal cooling
• Supplied with a standard 1/2" titanium horn that is suitable for many applications
• A wide range of dedicated accessories to meet special needs

---

BRANSON SONIFIER CELL DISRUPTOR MODEL S-250A, ½" horn
Solid state power supply rated at 200 watts, 240 volts meets FCC regulation and non-patient ground leakage specification. Features include load meter, automated amplitude compensation, broad band tuning, variable power control, 0 - 15 minute timer, electronic pulser. The sonifier 250 is supplied with a 1/2" diameter, tapped, threaded disrupter horn with flat replaceable tip. Model 102 converter, instruction manual and wrench kit.
E101-063-197 Sonifier Cell Disrupter Model S-250A, ½" horn

BRANSON SONIFIER CELL DISRUPTOR MODEL S-450A, ½" horn
Solid state power supply rated at 400 watts, 240 volts meets FOC regulation and non-patient ground leakage specification. Features include load meter, automated amplitude compensation, broad band tuning, variable power control, 0 - 15 minute timer, electronic pulser. The sonifier 450 is supplied with a 1/2" diameter, tapped, threaded disrupter horn with flat, replaceable tip. Model 102 converter, instruction manual and wrench kit.
E101-063-199 Sonifier Cell Disrupter Model S-450A, ½" horn ask stock?

BRANSON SONIFIER CELL DISRUPTOR MODEL S-450A, ¾" horn
Same as above, except supplied with a ¾" high gain step horn with solid tip, Model 102 converter, instruction manual and wrench kit
E101-063-201 Sonifier Cell Disrupter Model S-450A, ¾" horn

All of the Cell Disruptors operate at the most effective frequency of 20kHz

DIGITAL SONIFIER UNITS - Models S-250D & S-450D

• Datasheet for S-250D & S-450D

KEY FEATURES
Sonifier S-250D and S-450D digital ultrasonic processors include the same features as the analog units, but also offer these additional operator benefits:

• Two power levels
  - 200 Watt (S-250D)
  - 400 Watt (S-450D)
• Digital parameter setting with automatic parameter range validation
• Automatic end-point management using preset limits
• 80 character LCD display for process monitoring and alarm indication
• Printer interface with date stamp
• Broad process range from 1ml to over 500ml per sample
• RS-232 serial port for convenient computer interface
• Independent user I/O for remote start/stop control
• Internal self-diagnostic package to assure optimum performance
• Embedded multi-language software for operator convenience
• Supplied with a standard 1/2" titanium horn that is suitable for many applications
• A wide range of dedicated accessories to meet special needs

---

BRANSON DIGITAL SONIFIER CELL DISRUPTOR, MODEL S-250D, ½" horn
200 watts, 240V. Features include LCD digital wattmeter, 20 programmable pre-sets, variable power control, 10 hour timer, pulsing mode, footswitch jack and local, remote operation with print capability. Supplied with ½" dia horn.
E101-063-589 Digital Sonifier Cell Disrupter Model S-250D, ½" horn

BRANSON DIGITAL SONIFIER CELL DISRUPTOR, MODEL S-450D, ½" horn
400 watts, 240V. Features include LCD digital wattmeter, 20 programmable pre-sets, variable power control, 10 hour timer, pulsing mode, footswitch jack and local, remote operation with print capability. Supplied with ½" dia horn
E101-063-591 Digital Sonifier Cell Disrupter Model S-450D, ½" horn

BRANSON DIGITAL SONIFIER CELL DISRUPTOR, MODEL S-450D, ¾" horn
400 watts, 240V. Features include LCD digital wattmeter, 20 programmable pre-sets, variable power control, 10 hour timer, pulsing mode, footswitch jack and local, remote operation with print capability. Supplied with ¾" dia horn

E101-063-592 Digital Sonifier Cell Disrupter Model S-450D, ¾" dia horn ask stock?

SLP SERIES SONIFIER CELL DISRUPTORS
The BRANSON Sonifier SLP Series units – available in both time and energy (joules) models – are capable of processing today’s laboratory requirements. Software prevents inappropriate data entry and sounds an alarm if the process moves outside set limits.
The SLP Series units include the generator/power supply, converter, 1/8˝ microtip, all interconnects, and an I/O port for external control. They operate at 40 kHz, 50/60 Hz.

Features

• Autotune plus Memory (AT/M) – provides fully automatic tuning and stores frequency at the end of each cycle
• Digital parameter entry for precise, easy setup
• Digital amplitude control allows for critical applications (range from 10% to 100% in 1% increments)
• Continuous or pulsed operation
• LED readout displays parameter settings during setup and operation for easy reference and monitoring
• Provides storage of last-used cycle parameters even if the system is shut off or a power interruption occurs
• Local or remote (p/c) control capability
• Total processing time: 1 second to 99 hours (SLPt time mode model)
• Adjustable total energy: 1 to 10,000 joules (SLPe energy mode model)

SLPt (time), 150W and SLPe (energy), 150W - ask for more information.

Sonifier FAQ

HORNS & ACCESSORIES
for use with Sonifier Models 250 & 450
Please note that the ½" disruptor horn has greater intensity and is for volumes from 10 to 250mL. The ¾" dia horn is for volumes between 20 and 500mL.

Inquire for prices.

• Datasheets for Sonifier Accessories (For sound-reducing enclosure contact us with your requirements.)

Catalogue Number	Description
101-147-036	DISRUPTOR HORN 1/2” dia, stepped, tapped, threaded body with graduated depth scale
101-147-037	DISRUPTOR HORN 1/2” dia, stepped, tapped, threaded body (standard with Models 250 & 450) uses Flat Tip 101-148-013
101-147-038	DISRUPTOR HORN 1/2” dia, stepped solid, threaded body.
101-147-039	DISRUPTOR HORN 3/8” dia, stepped, solid, threaded body
101-147-043	DISRUPTOR HORN 3/4” dia, stepped, solid threaded body
101-147-040	EXPONENTIAL HORN 1/2” dia, tapped, Uses Flat Tip 101-148-024
101-147-041	EXPONENTIAL HORN 1/2” dia, solid
101-147-042	CATENOIDAL HORN 1/2” dia, solid
101-147-035	HIGH GAIN HORN 3/4” dia, stepped solid (optional with Model 450)
101-147-044	HIGH GAIN HORN 1” dia, stepped solid
101-147-046	CUP HORN, WATER JACKETED 1” I.D. high intensity with flow-through ports
101-147-047	CUP HORN Flow-through 2” dia, with transparent plastic body (requires adapter stud 100-098-249)
101-147-048	CUP HORN Flow-through 3” dia. with transparent plastic body
101-021-001	SEALED ATMOSPHERE TREATMENT CHAMBER ss. 3 - 10 mL **
Catalogue Number	Description
101-021-002	SEALED ATMOSPHERE TREATMENT CHAMBER ss 6 - 15 mL**
101-021-003	SEALED ATMOSPHERE TREATMENT CHAMBER ss 20 - 50 mL **
101-021-004	SEALED ATMOSPHERE TREATMENT CHAMBER ss. water jacketed, 3 - 10 mL **
101-021-005	SEALED ATMOSPHERE TREATMENT CHAMBER ss. water jacketed, 6 - 15 mL **
101-021-006	SEALED ATMOSPHERE TREATMENT CHAMBER ss. water jacketed, 20 - 50 mL **
211-118-010	OPEN ENDED WRENCH (for 1/2” disrupter tip)
101-148-013	FLAT TIP use with 1/2” tapped horn 1/4-20 thread
101-148-024	FLAT TIP use with 1/2” tapped horn 1/4-28 thread
101-147-049	HALF WAVE EXTENSION 1/2” dia with replaceable tip 101-148-013
101-148-062	TAPERED 1/8” MICRO TIP has 3-1/2 times the intensity (amplitude) of standard horn (for 1/2” tapped horn)
** use with horns which have threaded body
Catalogue Number	Description
101-148-069	TAPERED 3/16” MICRO TIP (for 1/2” tapped horn - 101-147-037)
101-149-070	TAPERED 1/4” MICRO TIP (for use with 1/2” tapped horn - 101-147-037)
101-063-212	DOUBLE STEP 1/8” MICRO TIP (coupler and lower portion) - Two piece horn for very small quantities and for low and medium power applications. Attaches directly to converter (standard 1/2” disrupter horn must be removed). Overall length 9-1/8” with 1/8” diameter in the lower 2-1/8”. Note: The double step micro tip lower portion is to be used only with its coupler
101-147-050	DOUBLE STEP 1/8” MICRO TIP coupler portion only (Refer 101-063-212)
101-148-063	DOUBLE STEP 1/8” MICRO TIP lower portion only (101-063-212)
100-098-249	ADAPTOR STUD
201-123-001	ROSETT COOLING CELL - Model 25, 8 - 25 mL (3 mL with micro tip)
201-123-002	ROSETT COOLING CELL - Model 50, 25 - 180 mL
201-123-003	ROSETT COOLING CELL - Model 250 35 - 300 mL
201-123-004	CONTINUOUS FLOW glass Rosett cooling cell. Use with horns which have threaded body
101-021-007	TISSUE DISRUPTOR ss. water jacketed

FOR USE WITH DISCONTINUED B-12; B-15 & B-30 SONIFIERS

Catalogue Number	Description
623-006-020	DISRUPTOR HORN 1/2” dia. stepped, tapped, with graduated scale
623-002-020	DISRUPTOR HORN 1/2” dia. stepped solid
623-001-020	DISRUPTOR HORN 3/8” dia stepped solid
603-002-020	EXPONENTIAL HORN 1/2 “ dia tapped
603-001-020	EXPONENTIAL HORN 1/2” dia. solid
609-001-020	CATENOIDAL HORN 3/4” dia. solid
623-004-020	DISRUPTOR HORN 3/4” dia. solid
101-151-003	CUP HORN 1” I.D. high density with Flow-through ports
109-067-684	CUP HORN Flow-through 2” dia with transparent plastic body 2,750.00 Requires adapter stud 100-098-249 for use with Model B30
109-067-685	CUP HORN Flow-through 3” dia. with transparent plastic body
200-042-017	SOUND REDUCING ENCLOSURE (for decreasing cavitation sound) 40 dB reduction. External dimensions 390 x 390 x 590mm high. The wall thickness is 35mm